Determination of Some Engineering Properties of Acha (Digitaria Exilis) and Sand Relevant to The Design of De-Stoning Machine

Authors

  • Boman James Bature NUHU BAMALLI POLYTECHNIC ZARIA
  • Nehemiah Aboshio
  • Elkanah Samuel Yayock
  • Alhassan Yahaya

DOI:

https://doi.org/10.33003/fjs-2026-1023-6411

Keywords:

acha, engineering properties, de-stoning

Abstract

This study evaluated selected physical, gravimetric, aerodynamic, and frictional properties of acha (Digitaria exilis) and sand relevant to the design of a de-stoning system. Measurements were conducted at a mean acha moisture content of 10.23% dry basis. One hundred randomly selected grains were measured for length, width, and thickness, while bulk density, true density, porosity, thousand-grain mass, angle of repose, coefficient of friction, terminal velocity, drag coefficient, and Reynolds number were determined using laboratory procedures. A sieve-gradation test was also performed on acha and sand using apertures from 2.36 mm to 106 μm. The mean length, width, and thickness of acha were 1.552, 0.853, and 0.791 mm, respectively; geometric mean diameter was 1.016 mm and sphericity was 65.50%. Mean thousand-grain mass, bulk density, true density, and porosity were 0.491 g, 598.9 kg m−3, 1127 kg m−3, and 46.90%, respectively. The mean angle of repose was 23.9°, while coefficients of friction were 0.44 on galvanized steel and 0.34 on fabric. The mean terminal velocity was 3.90 m s−1. For sand, mean thousand-grain mass, bulk density, true density, porosity, and angle of repose were 0.90 g, 1.45 g cm−3, 2.64 g cm−3, 45.08%, and 28.49°, respectively. The results indicate that density and frictional differences between acha and sand are potentially useful for gravity separation, while aerodynamic properties provide design parameters for air-assisted separation. The findings provide baseline engineering data for the development and optimization of acha de-stoning equipment

Author Biographies

  • Boman James Bature, NUHU BAMALLI POLYTECHNIC ZARIA

    Department of Agricultural and Bio-Environmental Engineering, School of Agricultural Technology,
    Senior Lecturer

  • Nehemiah Aboshio

    Department of Agricultural and Bio-Environmental Engineering, School of Agricultural Technology,
    Principal Lecturer

  • Elkanah Samuel Yayock

    Department of Agricultural and Bio-Environmental Engineering, School of Agricultural Technology,
    Principal Lecturer

  • Alhassan Yahaya

    Department of Agricultural and Bio-Environmental Engineering, School of Agricultural Technology

    Senior Lecturer

References

Baryeh, E. A., & Mangope, B. K. (2003). Some physical properties of QP-38 variety pigeon pea. Journal of Food Engineering, 56(1), 59–65. https://doi.org/10.1016/S0260-8774(02)00148-6

Jideani, I. A. (2012). Digitaria exilis (acha/fonio), Digitaria iburua (iburu/fonio) and Eluesine coracana (tamba/finger millet)—Non-conventional cereal grains with potentials. Scientific Research and Essays, 7(45), 3834–3843. https://doi.org/10.5897/SRE12.416

Jideani, I. A., & Jideani, V. A. (2011). Developments on the cereal grains Digitaria exilis (acha) and Digitaria iburua (iburu). Journal of Food Science and Technology, 48(3), 251–259. https://doi.org/10.1007/s13197-010-0208-9

Mirzabe, A. H., Khazaei, J., Chegini, G. R., & Gholami, O. (2013). Some physical properties of almond nut and kernel and modeling dimensional properties. Agricultural Engineering International: CIGR Journal, 15(2), 256–265.

Omobuwajo, T. O., Akande, A. E., & Sanni, L. A. (1999). Selected physical, mechanical and aerodynamic properties of African breadfruit (Treculia africana) seeds. Journal of Food Engineering, 40(4), 241–244. https://doi.org/10.1016/S0260-8774(99)00060-6

Pradhan, R. C., Said, P. P., & Singh, S. (2013). Physical properties of bottle gourd seeds. Agricultural Engineering International: CIGR Journal, 15(1), 106–113.

Satimehin, A. A., & Philip, T. K. (2012). Some physical properties of acha as affected by moisture content. Agricultural Engineering International: CIGR Journal, 14(4), 231–237.

Sirisomboon, P., Kitchaiya, P., Pholpho, T., & Mahuttanyavanitch, W. (2007). Physical and mechanical properties of Jatropha curcas L. fruits, and kernels. Biosystems Engineering, 97, 201–207.

Tunde-Akintunde, T. Y., & Akintunde, B. O. (2004). Some physical properties of sesame seed. Biosystems Engineering, 88(1), 127–129.

Ubbor, S. C., Arukwe, D. C., Ezeocha, V. C., Nwose, O. N., Iguh, B. N., & Nwibo, O. G. (2022). Production and quality evaluation of ready to eat extruded snacks from flour blends of acha-cowpea and sweet potato starch. FUDMA Journal of Sciences, 6(4), 245–253. https://doi.org/10.33003/fjs-2022-0604-1071

Zewdu, A. D. (2007). Aerodynamic properties of tef grain and straw material. Biosystems Engineering, 98(3), 304–309. https://doi.org/10.1016/j.biosystemseng.2007.08.003.

Determination of Some Physical Properties of Acha

Downloads

Published

16-11-2026

How to Cite

James Bature, B., Aboshio, N., Samuel Yayock, E., & Yahaya, A. (2026). Determination of Some Engineering Properties of Acha (Digitaria Exilis) and Sand Relevant to The Design of De-Stoning Machine. FUDMA Journal of Sciences, 10(23), 217-220. https://doi.org/10.33003/fjs-2026-1023-6411